顧名思義，防腐木就是防腐性能比較突出的木材，雖說防腐木的防腐、防霉、防蟲、防潮等性能比較突出，但是在如果沒有在施工和后期養護上注意一些事項，那么會大大降低其使用壽命。今天小編來為大家介紹
濟南防腐木施工及養護的注意事項，希望對大家有所幫助。
As the name suggests, anti-corrosion wood is a type of wood with outstanding anti-corrosion properties. Although anti-corrosion wood has outstanding anti-corrosion, mold, insect, and moisture resistance properties, if some precautions are not taken during construction and later maintenance, its service life will be greatly reduced. Today, the editor will introduce the precautions for the construction and maintenance of anti-corrosion wood in Jinan, hoping to be helpful to everyone.
一、選擇五金件銜接
1、 Choose hardware connection
五金件應用不銹鋼、熱鍍鋅或銅制的，主要防止日后生銹腐蝕，并影響銜接牢度。銜接裝置時請預先鉆孔，以防止防腐木開裂。
Hardware should be made of stainless steel, hot-dip galvanized or copper, mainly to prevent rust and corrosion in the future and affect the connection fastness. Please drill holes in advance when connecting the device to prevent cracking of the anti-corrosion wood.
二、注意留伸縮縫
2、 Pay attention to leaving expansion joint
裝置防腐木時，防腐木之間一般需留0。2至1CM的縫隙，縫隙大小由木材的含水率決定，木材含水率超越30%時不應超越0。8CM為好，可防止雨天積水及防腐木的收縮。此外，厚度大于50mm或者大于90mm的防腐方柱為減少開裂可在反面開一道槽。
When installing anti-corrosion wood, it is generally necessary to leave 0 between the anti-corrosion wood. A gap of 2 to 1CM, the size of the gap is determined by the moisture content of the wood. When the moisture content of the wood exceeds 30%, it should not exceed 0. 8CM is better to prevent water accumulation in rainy days and the shrinkage of anti-corrosion wood. In addition, anti-corrosion square columns with a thickness greater than 50mm or 90mm can be grooved on the opposite side to reduce cracking.
三、涂刷防護涂料
3、 Applying protective coatings
防腐木加工破損局部應涂刷防腐劑和戶外防護涂料。因防腐木本身是半廢品，粗糙局部可在鋪完后等木材含水率降到20%以下，再砂光一遍，如想有更好的效果，外表清潔潔凈后亦可涂刷戶外防護涂料。
The damaged parts of anti-corrosion wood processing should be coated with anti-corrosion agents and outdoor protective coatings. Due to the fact that anti-corrosion wood itself is semi waste, rough areas can be sanded again after the moisture content of the wood is reduced to below 20%. For better results, outdoor protective coatings can also be applied after the surface is clean.
四、及時打蠟
4、 Timely waxing
防腐木外表清潔可用一般洗濯劑來清洗，工具可用刷子;在后期使用中，需求定期，一般距離一年到一年半的時間，用木蠟油對防腐木外表做好維護處置，來加強其外表的防水防污性能。
The exterior of anti-corrosion wood can be cleaned with a general detergent, and tools can be cleaned with a brush; In the later use, it is necessary to regularly maintain and dispose of the anti-corrosion wood surface with wood wax oil, usually from one to one and a half years, to strengthen its waterproof and anti fouling performance.
五、做好維護
5、 Maintain well
防腐木外表用防護涂料或油基類涂料涂刷完后，為了達到效果，48小時內防止人員走動或重物挪動，以免毀壞防腐木面層已構成的維護膜。如想獲得更優良的防臟效果，必要時面層再做兩道專用戶外清漆處置。
After the anti-corrosion wood surface is coated with protective paint or oil-based paint, in order to achieve the effect, personnel or heavy objects should be prevented from moving within 48 hours to avoid damaging the maintenance film formed by the anti-corrosion wood surface layer. If you want to achieve better anti dirt effect, if necessary, apply two additional coats of specialized outdoor varnish on the surface layer.
The above is the relevant content on precautions for anti-corrosion wood construction and maintenance, hoping to be helpful to everyone! If you have any needs or doubts about this, please feel free to contact us at any time http://www.puwff.com consulting service
傳真：0531-86370030
